Official Silverback video workshop

Silverback SRS Monopod Installation Guide

This official Silverback video demonstrates how the monopod is fitted to an SRS stock after the stock panels have been removed. Use this guide when you need to follow the short installation sequence visually, from the exposed stock mounting position through insertion, upright positioning and tightening with the specified 20 mm wrench.

Complete guide Official video
Primary source
SRS
Official Silverback video workshop
Source-based overview
0:40
Evidence standard
Silverback SRS Monopod Installation Guide
5step by step
0:40Video
2Tools and parts explicitly identified
SRSplatform hub

01Source-based overview

What this procedure does

The installation begins only after the stock panels have been removed. Silverback’s description identifies the compatible platforms as the SRS-A1 and SRS-A2 and links to a separate tutorial for stock-panel removal. In the installation footage, the exposed stock mounting position is prepared for the monopod, and on-screen text identifies a 20 mm wrench for the tightening stage.

The operator then inserts the monopod into the stock mounting position, holds it upright and tightens its retaining hardware with the 20 mm wrench. The later frame shows the completed installation. The five checkpoints below follow that visible progression without treating the separate stock-panel-removal tutorial as part of this video.

Tools and parts explicitly identified

  • 20 mm wrench
  • monopod

Evidence standard

Every technical statement below is restricted to the official Silverback description, subtitles, on-screen text or visible action. Unstated torque values and compatibility claims are intentionally omitted.

What the footage makes clear

This walkthrough stays close to the official Silverback source. The expanded notes explain what is visible at each checkpoint, while measurements, compatibility and cautions remain limited to what Silverback actually states.

  • The official video description establishes the SRS-A1 / SRS-A2 compatibility and the stock-panel-removal prerequisite.
  • Visual review observations establish the 20 mm wrench text, monopod insertion, upright positioning, retaining-hardware tightening and completed installation.
  • The supplied transcript evidence states that no official or automatic English or French subtitle track was available.
Specification Source value
Compatible platforms SRS-A1 / SRS-A2
Wrench 20 mm
Which Silverback platforms does this monopod installation cover?Which tools or parts are identified for Silverback SRS Monopod Installation Guide?

02Primary source

Watch the official Silverback tutorial

Every technical statement below is restricted to the official Silverback description, subtitles, on-screen text or visible action. Unstated torque values and compatibility claims are intentionally omitted.

What should I watch for before Begin with the stock panels removed?Where does the official video show View the completed installation?

03Procedure

Silverback SRS Monopod Installation Guide, step by step

SRS The stock is shown with its panels removed, leaving the mounting position ready for the monopod.
The stock is shown with its panels removed, leaving the mounting position ready for the monopod.
SRS The monopod is being fitted into the exposed stock mounting position.
The monopod is being fitted into the exposed stock mounting position.
SRS The inserted monopod is held upright while its fit in the stock is maintained.
The inserted monopod is held upright while its fit in the stock is maintained.
SRS The 20 mm wrench is used on the monopod’s retaining hardware.
The 20 mm wrench is used on the monopod’s retaining hardware.
01Begin with the stock panels removedAt this opening checkpoint, the stock-panel removal prerequisite has been met and the stock mounting position is exposed. Compare the frame with the source description: the monopod installation is not begun until the stock panels are removed. The visible mounting position sets up the next checkpoint, where the monopod is placed into the stock. Video: 00:18 ↗
02Insert the monopodWith the mounting position exposed, the operator inserts the monopod into the stock. The important visual comparison is the monopod entering the stock mounting position rather than being shown separately from it. Once it is inserted, the sequence moves to holding the monopod upright before the retaining hardware is tightened. Video: 00:22 ↗
03Hold the monopod uprightAt this checkpoint, the inserted monopod is held upright in the stock mounting position. Compare the frame for the monopod’s upright presentation before moving on to the tightening stage. This position connects the fitting operation to the retaining hardware, which is tightened with the 20 mm wrench shown in the video. Video: 00:25 ↗
04Tighten the retaining hardwareThe operator uses the 20 mm wrench to tighten the monopod’s retaining hardware. The on-screen tool detail is specifically 20 mm, so that is the source-defined wrench size to compare with this frame. After this tightening action, the footage proceeds to the completed installation view. Video: 00:29 ↗
05View the completed installationThe final checkpoint shows the monopod installed in the stock mounting position after the retaining hardware has been tightened. Compare this frame with the earlier upright positioning: the monopod remains fitted to the stock and the video presents the installation as complete. This is the endpoint of the sequence shown in the official tutorial. Video: 00:33 ↗
Source-stated cautions
  • It is necessary to remove the stock panels before this operation.
Checks shown or stated
  • The monopod is shown installed in the stock mounting position.
  • The retaining hardware has been tightened with the 20 mm wrench.
  • The video shows the completed installation.
How do I complete Begin with the stock panels removed safely?What must I check after View the completed installation?

04FAQ

SRS tutorial questions

Which Silverback platforms does this monopod installation cover?

The official description covers the SRS-A1 and SRS-A2.

What must happen before the monopod installation?

The stock panels must be removed before this operation. Silverback provides a separate stock-panel-removal tutorial.

What wrench size is shown for tightening?

The on-screen text specifies a 20 mm wrench.

Complete guide SRSShop the platform: SRS
Which Silverback platforms does this monopod installation cover?What must happen before the monopod installation?
0 commentson Silverback SRS Monopod Installation Guide

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.
Skirmshop AI