Official Silverback video workshop

Silverback Carbon Barrel Extension Installation Guide

This official Silverback video demonstrates how the carbon barrel extension is assembled around the protruding inner barrel, from positioning the barrel spacer to engaging the muzzle cap. Use this guide when following the installation footage and when checking the configuration limits that Silverback publishes for SRS and TAC-41 setups.

Complete guide Official video
Primary source
SRS and TAC-41
Official Silverback video workshop
Source-based overview
4:53
Evidence standard
Silverback Carbon Barrel Extension Installation Guide
5step by step
4:53Video
9Tools and parts explicitly identified
SRS and TAC-41platform hub

01Source-based overview

What this procedure does

The footage begins with the operator choosing a barrel-spacer position on the protruding inner barrel, fixing that position with tape, and using a tube to push the spacer into the carbon extension. The rear adapter is then installed and its alignment checked before the small retaining screws are set. Once the extension sections are joined, the front spacer is installed, creating the visual sequence that leads to the muzzle-end finishing steps.

Silverback states that the extension is designed for direct use on 24 mm threaded SRS G-Spec A1 and A2 barrels and SRS Sport 16-inch and 20-inch barrels. Other barrels require a DT muzzle brake and timing shims. The supplied spacer quantity depends on the model: one for XS, two for S/M/L, and three for XL. Silverback also suggests keeping the inner barrel at least 100 mm shorter than the chart maximum, and the video identifies filling the last 10 cm with foam as optional for integral-silencer use.

Tools and parts explicitly identified

  • Tape
  • Tube
  • Barrel spacer(s)
  • Rear adapter
  • Small retaining screws
  • Carbon barrel extension sections
  • Front spacer
  • Foam
  • Muzzle cap

Evidence standard

Every technical statement below is restricted to the official Silverback description, subtitles, on-screen text or visible action. Unstated torque values and compatibility claims are intentionally omitted.

What the footage makes clear

This walkthrough stays close to the official Silverback source. The expanded notes explain what is visible at each checkpoint, while measurements, compatibility and cautions remain limited to what Silverback actually states.

  • The five chronological checkpoints are taken from the official video’s visual review observations at 25, 64, 142, 233, and 275 seconds.
  • Direct compatibility, mounting requirements, inner-barrel guidance, spacer quantities, and foam-filling limits come from the official Silverback video description.
  • The visible on-screen wording about optional foam filling is based on the visual review observation; no official subtitle track was available.
Specification Source value
Direct outer-barrel compatibility 24 mm threaded outer barrels: SRS G-Spec barrels (A1 & A2) and SRS Sport barrels (16’’ & 20’’)
Other-barrel mounting DT muzzle brake and a set of timing shims
Minimum suggested inner barrel length 100 mm shorter than the maximum length
Barrel spacer quantity 1 piece for the XS model, 2 pieces for S/M/L models, and 3 pieces for the XL model
Integral silencer foam filling up to 100 mm (suggested) of foam filling on the muzzle side
Which outer barrels accept the carbon barrel extension directly?Which tools or parts are identified for Silverback Carbon Barrel Extension Installation Guide?

02Primary source

Watch the official Silverback tutorial

Every technical statement below is restricted to the official Silverback description, subtitles, on-screen text or visible action. Unstated torque values and compatibility claims are intentionally omitted.

What should I watch for before Position the barrel spacer?Where does the official video show Engage the muzzle cap?

03Procedure

Silverback Carbon Barrel Extension Installation Guide, step by step

SRS and TAC-41 A taped spacer position is transferred into the carbon extension with a tube.
A taped spacer position is transferred into the carbon extension with a tube.
SRS and TAC-41 The rear adapter is seated, aligned, and held with its small retaining screws.
The rear adapter is seated, aligned, and held with its small retaining screws.
SRS and TAC-41 Joined extension sections show the front spacer installed at the muzzle end.
Joined extension sections show the front spacer installed at the muzzle end.
SRS and TAC-41 On-screen text marks the last 10 cm of foam as optional for integral-silencer use.
On-screen text marks the last 10 cm of foam as optional for integral-silencer use.
01Position the barrel spacerThe operator selects a position for the barrel spacer on the protruding inner barrel, fixes that position with tape, and uses a tube to push the spacer into the carbon extension. Compare the frame with the spacer’s chosen location and the taped position; this establishes the placement that the following adapter and extension assembly will use. Video: 00:25 ↗
02Install and align the rear adapterThe rear adapter is installed at the back of the carbon extension, and the operator checks its alignment before setting the small retaining screws. The important visual checkpoint is the adapter’s alignment in the assembled rear section; once it is checked and retained, the extension sections can be joined. Video: 01:04 ↗
03Join the extension sectionsThe carbon extension sections are joined, and the front spacer is installed at the muzzle end. Look for the sections meeting as one assembly and for the spacer appearing at the front before moving on to the optional muzzle-side filling and cap sequence. Video: 02:22 ↗
04Review the optional foam fillingThe on-screen message identifies an optional way to use the barrel extension as an integrally suppressed barrel: filling the last 10 cm with foam. The visual checkpoint is the muzzle-side area referenced by that message; after this optional choice is considered, the sequence proceeds to the muzzle cap. Video: 03:53 ↗
05Engage the muzzle capAt the final checkpoint, the muzzle cap is engaged on the assembled carbon barrel extension. Compare the frame with the cap seated at the muzzle end; this is the visible closing step after the spacer, adapter, joined sections, and optional foam instruction have been shown. Video: 04:35 ↗
Source-stated cautions
  • To use the extension on any barrels other than the listed 24 mm threaded SRS outer barrels, use a DT muzzle brake and a set of timing shims.
  • Do not skip the muzzle-brake timing procedure unless the muzzle brake is screwed all the way onto the outer-barrel thread, ending in an unrealistic position.
  • For concentricity reasons, Silverback suggests respecting a minimum inner barrel length 100 mm shorter than the maximum length shown in the chart.
Checks shown or stated
  • The rear adapter alignment is checked before the small retaining screws are set.
  • The extension sections are visibly joined and the front spacer is installed.
  • The muzzle cap is engaged at the muzzle end.
How do I complete Position the barrel spacer safely?What must I check after Engage the muzzle cap?

04FAQ

SRS and TAC-41 tutorial questions

Which outer barrels accept the carbon barrel extension directly?

Silverback specifies direct use on 24 mm threaded SRS G-Spec barrels (A1 & A2) and SRS Sport barrels (16’’ & 20’’).

What is required for other outer barrels?

Silverback states that other barrels require a DT muzzle brake and a set of timing shims. The muzzle brake must also be properly timed, except in the stated case where it is screwed all the way onto the outer-barrel thread and ends in an unrealistic position.

How many barrel spacers are supplied?

The extension is delivered with one spacer for the XS model, two for S/M/L models, and three for the XL model. The video shows the operator choosing the spacer position on the protruding inner barrel and pushing it into the extension with a tube.

Complete guide SRSComplete guide TAC-41Shop the platform: SRS and TAC-41
Which outer barrels accept the carbon barrel extension directly?What is required for other outer barrels?
0 commentson Silverback Carbon Barrel Extension Installation Guide

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.
Skirmshop AI